#Freenas iso to usb how to#
#Freenas iso to usb download#

Again, once the data was cached at the NAS, the read speed for FTP was around 100MB/sec. Although, in a direct FTP to the FreeNAS serverвЂ™s FTP daemon, the transfer rate (upload) of 7.5MB/sec confirms the relatively poor write performance of the drive system. It is easy to see that more rigorous testing would be needed to gauge the performance of the FreeNAS system, however that testing is beyond the scope of this blog entry. However, the вЂњactualвЂќ write took much longer due to write caching from VMware: Running a test using pure-ftpd on the SLES virtual server from my workstation (1Gbps) to the servers disk (a vmdk on the iSCSI SAN provided by FreeNAS) the вЂњperceived throughputвЂќ from the ftp client was about 100MB/sec: ftp> put w2kadv.isoДЎ00% |***************************************************| 405 MB 105.85 MB/s 00:00 ETAДў26 3.833 seconds (measured here), 105.83 Mbytes per secondД¤25406464 bytes sent in 00:03 (105.83 MB/s) On boot of the VM, the SAN peaked at 60MB/sec (read)В for a few seconds. Installation was via NFS-mounted CD-ROM image so that would be a limiting factor. VMware ESX 3i Discovers FreeNAS Target with EaseДЄn installation of Suse Linux Enterprise Server (SLES)В 10 SP2 (x86_64) went swimmingly with an average write-to-SAN rate of 8MB/sec and peaks to 20MB/sec (write). Next, I mounted each as вЂњshare1вЂќ and вЂњshare2,вЂќ respectively, to provide two separate вЂњvolume containersвЂќ to house my iSCSI target extents. Using my two RAID1 disks provided by the LSI 1068E and four 500GB RAID-edition hard disks, I formatted two volume as UFS (GPT and Soft Updates), naming them вЂњvolume1вЂќ and вЂњvolume2,вЂќ respectively.

Create UFS/Soft Updates filesystem volumes (one per RAID1).

Make sure BIOS is configured for boot-from-flash (see вЂњPreparing the BIOSвЂќ in my blog вЂњ Installing VMware ESXi on the Tyan Transport GT28вЂќ for details and screen shots).

Plug-in your USB device into your target platform.

(note: my device is вЂњ/dev/sdiвЂќ вЂ“ use yours from step 3) Gunzip -c /FreeNAS-amd64-embedded-xxx.img | dd of=/dev/sdi

Even though this image is a вЂњ.imgвЂќ file, it is gzipped, so it needs to be extracted to your target volume:.

dev/sdi, so вЂњumount /dev/sdi1вЂќ works for my SanDisk Cruzer) If your system вЂњauto mountsвЂќ the drive, manually unmount all partitions associated with the вЂњthumb driveвЂќ and make note of the device (ex.Insert target USB вЂњthumb driveвЂќ into a compatible USB socket.

#Freenas iso to usb download#

Download the AMD64 вЂњFreeNAS ImageвЂќ from.Since I am still testing the Tyan Transport GT28 system, I will catalog my steps for that platform: NOTE: Your BIOS must support boot-from-USB or this will not work. That said, letвЂ™s quickly run-down a 1, 2, 3 approach for booting FreeNAS to hardware from USB driveвЂ¦ This is a run-from-ram-disk appliance, so the size of the USB storage device is minimal: about 50-60MB. Given that M0n0wall and pfSense both virtualize very well, I have no doubt the VMware appliance version performs likewise. In short, this is a no-nonsense and easy-to-install appliance-oriented distribution that covers the basics of network attached storage: CIFS, NFS and iSCSI. The look-and-feel is very M0n0wall-ish as well. This week, that question has been вЂњhave you tried FreeNAS?вЂќДЄnyone familiar with the fine m0n0wall project (and off-shoot pfSense) will instantly recognize the FreeBSD appliance approach taken for FreeNAS.

However, any time I come across the same simple question so many times in one week I have to investigate it more thoroughly.

#Freenas iso to usb how to#

I donвЂ™t want to get too deep into a re-hash of how to install FreeNAS onto USB flash (or вЂњthumbвЂќ) drives вЂ“ there is a wealth of community information in that regard.